Standard relays included with RIGID wire harnesses are 12V. If your RIGID LED light project has a 24V electrical system, you will need to replace the 12V relay with this 24V relay for proper functionality.
Standard relays included with RIGID wire harnesses are 12V. If your project has a 24V electrical system, you will need to replace the 12V relay with a 24V relay for proper functionality.
Rigid Industries 6 Amp LED Flasher - 2 Output - 12 Volt
This RIGID 6 amp flasher module provides seven flashing options for your LED lighting components. It is easy to install and works off of the auxiliary switch to your lights. This model features the following modes: Double Alternating: Alternates flashing twice per side. Quad Alternatiing: Alternates flashing four times in quick succession per side. Quint Alternating: Alternates flashing five times in quick succession per side. Mega Alternating: Alternates one bright flash per side. Double Simultaneous: Both sides flash twice simultaneously in quick succession, followed by a short pause. Quad Simultaneous: Both sides flash four times simultaneously in quick succession, followed by a short pause. Random: Randomly cycles through all previous modes. This model is specifically designed to be installed into a 12V electrical system only.
Rigid Industries 3 Amp LED Flasher - 2 Output - 12 Volt
This RIGID 3 amp flasher module provides seven flashing options for your LED lighting components. It is easy to install and works off of the auxiliary switch to your lights. This model features the following modes: Single Simultaneous: Both sides flash once simultaneously, followed by a short pause. Double Simultaneous: Both sides flash twice simultaneously in quick succession, followed by a short pause. Quad Simultaneous: Both sides flash four times simultaneously in quick succession, followed by a short pause. Alternating: Alternates flashing once per side. Alternating variable speed: Same as mode 4, but at multiple speeds. Simultaneous variable speed: Same as mode 1, but at multiple speeds. Random: Randomly cycles through all previous modes. This model is specifically designed to be installed into a 12V electrical system only.
The Radiance 3 wire multi-trigger harness is designed specifically for RIGID Radiance LED light bars. Equipped with two independent circuits for an easy install, circuit one is designed for higher amperage and utilizes a relay to power the primary LEDs on the Radiance light bar while circuit two is designed for low amperage and has no relay for the backlighting circuit on the Radiance. The Radiance multi-trigger harness also comes standard with two separate backlit LED rocker switches, 1 red, 1 blue, each circuit can be used independently. Fits 10-50 in. Radiance and 10-54 in. Radiance Curved LED light bars.
Rigid Industries Harness used for set of Dually Lights
This 14 foot/4.3 meter wiring harness is designed to connect a pair of D-Series LED lights to your 12V electrical system. It features battery terminals on one end and Deutsch connectors on the other to connect to the lights. It incorporates an inline fuse holder, and a waterproof switch. This harness is compatible with the following RIGID LED Lights: D-Series PRO Pair and SR-Q Series PRO Pair Spot, Flood or Flood Diffused Optics.
Rigid Industries Harness used for 4in/ 6in/ Single Dually/ D2
This 11 foot/3.35 meter wiring harness is designed to connect a single LED light to your 12V electrical system. It features battery terminals on one end and a Deutsch connector on the other to connect to the light. It incorporates an inline fuse holder, and a waterproof switch. This harness is compatible with the following RIGID LED Lights: D-Series single, 4 in. E-Series, 6 in. E-Series PRO, 6 in. SR-Series, 10 in. SR-Series, Q-Series single, D-XL Series single, SR-M Series single, SR-Q Series single.
Rigid Industries Harness used for 10in-30in Light Bars
This 11 foot/3.35 meter wiring harness is designed to connect a single LED light bar to your 12V electrical system. It features battery terminals on one end and a Deutsch connector on the other to connect to the light. It incorporates an inline fuse holder, a 12V relay, and a waterproof switch. This harness is compatible with the following RIGID LED Lights: 20 in.-50 in. SR-Series PRO and 10 in.-30 in. E-Series PRO Light Bars.
This RIGID switch features a lighted rocker with protective rubber boot and is a great addition to any RIGID lighting system. This switch will fit all RIGID wiring harnesses. This product requires a 3/4 in. hole to mount.
Rigid Industries Hi/Po Harness used for 40in-50in Light bar
This 13 foot/4 meter wiring harness is designed to connect a single LED light bar to your 12V electrical system. It features battery terminals on one end and a Deutsch connector on the other to connect to the light. It incorporates an inline fuse holder, a 12V relay, and a waterproof switch. This harness is compatible with the following RIGID LED Lights: 40 in.-50 in. E-Series PRO, 20 in.-54 in. RDS-Series PRO.
This three position switch features a lighted cherry rocker with a protective rubber boot and is a great addition to any RIGID lighting system. This RIGID switch allows for on, off, or auto when the vehicle is in reverse. This product requires a 3/4 in. hole to mount.
Use RIGIDs Pendant Switch Kit if you don't want to drill a hole in your vehicle to mount a switch. This Kit works great for powersports applications. Ultra-durable, waterproof, dust-proof and impact resistant. LED on/off indicator light. Kit includes switch, 3M VHB mounting tape and radius mount pad for bar mounting.
KC LKZ M10-1.5 Light Locks provide anti-theft security for KC FLEX ERA 3, FLEX ERA 4, LZR LEDs, KC Gravity G34/G46/Pro6/Pro-Sport LEDs, and KC FLEX LED Singles/Duals. 100% CNC machined steel with an anti-corrosive Zinc coating.
KC LKZ M8-1.25 Light Locks provide anti-theft security for all FLEX LED and Gravity LED Pro6 Light Bars. Made from 100% CNC machined steel with an anti corrosive Zinc coating for long lasting performance and durability.
KC HiLiTES Wiring Harness w/40 AMP Relay & LED Rocker Switch (Up to 2 - 130w Lights)
KC Hilites 6315 Relay Wiring Harness Kit allows for quick installation for up to two 130w lights. Harness complete with 40A relay, illuminated rocker switch kit, fuses and mounting hardware to handle up to 260w.
KC HiLiTES Wiring Harness FLEX ERA w/40 AMP Relay & 3 Position LED Rocker Switch (3-Pin Deutsch Con)
KC 6311 FLEX ERA 3-Pin DT Wiring Harness Relay Kit allows for quick installation for up to two 130w lights. Harness complete with 40A relay, 3 position illuminated rocker switch kit, fuses, and mounting hardware.
KC HiLiTES Wiring Harness for (2) Lights w/2-Pin Deutsch Connectors (110w Max Total)
The KC Universal Wire Hider is as simple as it sounds. It is a 3.3 ft strip of rubber extrusion that has an internal channel to help you hide your wires for a clean install of off-road lights and other accessories.
KC HiLiTES FLEX ERA 1 Single Light Shield ONLY (Amber)
Amber Light Shield for KC(R) FLEX ERA(R) 1 Lights. Take your FLEX ERA 1 lights' performance to new heights with amber light shields providing additional protection from the elements allowing you to Adventure Further(R).
KC(R) FLEX ERA(TM) 3 AMBER LIGHT SHIELD FOR ADDED PROTECTION AND VISIBILITY KC's FLEX ERA(TM) 3 lights and light bars are one of the most capable LED lights available today. Take your FLEX ERA 3 lights' performance to new heights with amber light covers providing additional protection from the elements allowing you to Adventure Further(R).
KC HiLiTES Replacement Lens/Reflector for 6in. Halogen Lights (Spot Beam) - Single
The KC 4213 6" replacement Spot Beam clear lens/reflector for all KC Hilites 6" Apollo, Daylighter and Slimlite Halogen lights. Complete with glass Lens and H3 Bulb Adapter. Spot Beam pattern for focused range and high speed visibility.
KC HiLiTES 3300 12 Volt Relay - 5 Pole is standard equipment for all KC HiLiTES 12v Light Kit Applications. Relay uses 5 poles and is sealed for added moisture protection. For use with 12v Applications only.